WHY CHOOSE ModernTiling

There are a number of tiling companies in Dublin, however it’s always the most essential to trust and pick. Your single click when searching for “local tilers near me” online or calling somebody over the phone can help you discover a tiler in Dublin. Choosing the best tiling system in Dublin can be a difficult job.

We are a certified and certified tiling agency in Dublin. Having a number of years of experience and skilled commercial tilers in Dublin, we can mesmerize the appearance of your location with our stunning ceramic tiles.

How to Prepare a Wall for Tiling (Detailed + Top Tips).


Preparing your walls for a fresh wall tile setup is easy and problem-free with our no-nonsense guide at the ready.

You can set up new tiles on different surface areas, as long you prepare the wall properly. Simply ensure the surface area is level enough, and dust and dirt-free– and that there are no indications of recurring wetness. When proper preparation is done, you can easily use adhesive and stick your fresh tiles straight onto the wall.

How to prepare for tiling a wall:.

  • Eliminate old fittings, such as pins, screws, rivets and so on
  • Repair or eliminate unsuited plaster.
  • Eliminate or pre-treat wallpaper (if present).
  • Fix any fractures or signs of damage.
  • Level the surface area.
  • Sand, so that the adhesive can bond.
  • Ensure the surface is dirt, grease-free and dust.
  • Choose the proper guide for your kind of surface.

Other important preparation to do prior to you begin:

  • Measure your square video.
  • Figure out the number of tiles required for the task.
  • Buy at least 10% more tiles in case of breakage during the installation. You might wish to increase the amount to 20% or even 30% additional if you’re about to install delicate patterns. There are no assurances when it pertains to discovering the exact same batch, or perhaps one that will carefully resemble what you purchased, further down the line, so this is extremely advised.

Make sure you have the ideal kind of adhesive.

According to the expert tradesmen from Great Tilers, less knowledgeable DIY enthusiasts can utilize the ready-mix type of adhesive, however a professional tiler will always use the powdered option. It dries slower and hence permits you to better change and line up the entire wall tiling.

Handy suggestion: When tiling kitchen splashbacks or wet rooms, or installing restroom tiles in general, adhesive need to be waterproof.

Make sure the wall is level or your tile setup might not achieve success.

Tiling an unequal wall has the prospective to result in disaster. A simple method to spot irregularities is by positioning something long and flat (i.e. a regular plank) on the wall and moving it throughout. By doing this, you can identify any inflamed locations or bumps, ought to they exist.

An unequal wall can avoid adhesive from sticking– which might trigger your whole wall setup to collapse. According to expert tilers, anything between 3 and 6mm is still convenient– but anything beyond that is most likely to cause trouble.

If you choose to apply a somewhat thicker layer of adhesive to compensate, its grip may loosen up– leading to undesirable issues further down the line.

Different surfaces require various ways of preparation.

Some surfaces, such as a fresh drywall, require at least a month to correctly dry. Other cases, such as when you’re tiling on wood, require a coat of polyurethane paint. Ensure you have the ideal service for your specific wall and, whenever in doubt, speak with a professional tiler.

Tile board backers are a fantastic method to deal with unequal surface areas with minimal effort.

Slightly costlier, tile board backers can assist you resolve the issue– not to mention that these items are resistant to moisture, and can effectively avoid mould (which is known to grow on permeable products in warm, wet conditions). This benefit makes tile backer boards a practical option for locations, showers and restrooms surrounding the kitchen sink.

The one disadvantage of tile backer boards is that utilising such products will make your fresh tile setup a little bit more costly.

Valuable idea: One important thing to make sure of here is that the boards are well-mounted and strong.

Can you set up brand-new tiles on top of old tiles?

Tiling over old tiles is possible– but it’s always much better to retile and get rid of.

Many tiles are too smooth for adhesive to correctly bond and, in these cases, additional treatment is needed. Depending upon the toolkit you have at hand, you might either try a sander (with medium to coarse sandpaper) or a grinding disc. You should, nevertheless, show extra care so as not to damage the integrity of your old tiling.

Important: Always check for void behind old tiles. To do this, just knock on each piece with your hand and listen out for hollow sounds. Locations with hollow space are simple to find, but beware– if you fail to identify these and tile over them anyhow, you run the risk of having your fresh tiles collapse in the reasonably future.

tiling tools

What tools will I need for a DIY tile setup?

  • Paintbrush.
  • Paint roller.
  • Liquid waterproofing membranes (or plastic sheets).
  • Routine energy knife.
  • Stapler.
  • Mask and protective glasses (to keep you safe from heavy particles).
  • Gloves.
  • Straight edge (or a comparable tool).
  • Pencil.
  • Determining tape.
  • Drill.
  • Pins (to support the tile up until the adhesive bonds and dries off).
  • Level.

Essential: Ensure your surface is always dust, dirt and moisture-free or there’s an opportunity your adhesive may not effectively bond.

For the majority of types of masonry, ceramic and vinyl tiles will stick– but for wooden surfaces, you’ll need to use a coat of paint or prime.

How do I prep drywall for a fresh tile setup?

Fresh drywall requires approximately a month prior to it’s ready for tiling, however when the time comes, you won’t need to tape the joints. All you’ll need to do is apply a skim coat and sand. As soon as done, clean the surface area from dust, dry any indications of moisture and apply the adhesive.

Crucial: For locations rich with wetness, use water-resistant plasterboard.

How do I prep old drywall for a fresh tile installation?

It’s important to properly evaluate whether the wall is stable and strong enough to hold the weight of fresh tiling. You ought to always ask for advice from a knowledgeable tiler if you’re uncertain.

Complete any fractures or holes from pins, nails or any other kind of wall fitting, use the primer, leave it to dry, sand one more time, and after that apply the adhesive.

How do I prep the wall for tiles if the drywall is already painted or textured?

According to specialists, you ought to use PVA or make a Do It Yourself guide by adding a bit more water to your adhesive.

After that, there are a few crucial jobs to take care of:.

  • Eliminate diminished paint.
  • Repair cracks and holes.
  • If bumps are present, sand.
  • Clean the surface.
  • Ensure there are no indications of oil or grease.

Valuable pointer: Treat the wall with Trisodium Phosphate (TSP). It’s a powerful cleaner, stain eliminator and degreaser– however bear in mind that this should, of course, be kept well away from children.

How do I prep a plywood surface for fresh tiling?

The reality is that plywood appropriates for tiling your floors however not as useful when it comes to walls. The product is made of compressed wood mixed with different oils, which suggests that heat can impact it. If exposed to regular and remarkable modifications in temperature level, tiles and grout will likely split.

How do I prep a wallpapered wall for tiling?

When it concerns walls, tiles offer even more durability and practicality than wallpaper, and the very best choice is to eliminate wallpaper anywhere possible. The most efficient and hassle-free way is by exposing the space to steam– but this approach does come with some dangers. The high temperature levels and moisture can possibly cause damage which is often beyond basic repair work if you’re treating drywall or engineered wood through steam.

You can merely wipe the surface area with a warm and damp rag. This way, wetness will not permeate through to the substrate itself– however at the same time, the wallpaper will relax. Repeat the treatment a couple of times and utilize a scraper to peel whatever with minimal effort.

Once done, all you’ll require to do prior to applying guide or adhesive is to make certain the surface is tidy and dry.

You can set up brand-new tiles on numerous surfaces, as long you prepare the wall properly. When correct preparation is done, you can easily use adhesive and stick your fresh tiles straight onto the wall.

Locations with hollow area are easy to identify, however beware– if you stop working to find these and tile over them anyhow, you run the risk of having your fresh tiles collapse in the reasonably near future.

The truth is that plywood is ideal for tiling your floors but not as practical when it comes to walls. When it comes to walls, tiles use far more durability and usefulness than wallpaper, and the best alternative is to get rid of wallpaper wherever possible.

Watch this video and learn how to tile kitchen wall

Tilers (WikiPedia)

Tiles are usually thin, square or rectangular coverings manufactured from hard-wearing material such as ceramic, stone, metal, baked clay, or even glass. They are generally firm in place in an array to lid roofs, floors, walls, edges, or new objects such as tabletops. Alternatively, tile can sometimes dispatch to thesame units made from lightweight materials such as perlite, wood, and mineral wool, typically used for wall and ceiling applications. In substitute sense, a tile is a construction tile or same object, such as rectangular counters used in playing games (see tile-based game). The word is derived from the French word tuile, which is, in turn, from the Latin word tegula, meaning a roof tile composed of passionate clay.

Tiles are often used to form wall and floor coverings, and can range from easy square tiles to mysterious or mosaics. Tiles are most often made of ceramic, typically glazed for internal uses and unglazed for roofing, but extra materials are also commonly used, such as glass, cork, concrete and supplementary composite materials, and stone. Tiling stone is typically marble, onyx, granite or slate. Thinner tiles can be used on walls than on floors, which require more durable surfaces that will resist impacts.

Related Articles (Tilers)

Our Services

Around The Web(Tilers)

Call Now Button